Ventoy windows 10 not working11/10/2023 ![]() Becareful when you choose the disk, don't select your system disk by mistake.Ģ. Ventoy LiveCD System Instructions (GUI mode since 1.0.54)ġ. Use Ventoy LiveCD iso file in CD/DVD and boot the VM to enter the LiveCD system. As follows, the number in the red frame is corresponded to PhysicalDrive0/1/2. You must close and reopen the VMware program when plug-in and plug-out the USB stick or the There are two ways for you to use to confirm:Ĭompare the list when you plug-in and plug-out the USB stick and check the difference. Note that when selecting the last step, make sure that the USB drive corresponds to PhysicalDrive0 or PhysicalDrive1 or other. 6.2 Delete the default disk, and add the USB drive as a disk to the VM.Finally enter the LiveCD OS and then follow the prompts at the end of this article.Ĭreate a new VM with all default configurations. Restart your computer (better to cold restart), change the BIOS mode to UEFI and boot the USB drive. 5.3 Reboot your computer, and select USB boot option in UEFI mode.Get the EFI directory and copy it to the root of the FAT32 partition above. Ventoy LiveCD,for example ventoy-1.0.20-livecd.iso has only an EFI directory in it. 5.2 Extract the files in the LiveCD to the USB drive.4GB) and format the small partition with FAT32 filesystem. You can create a small partition by diskpart (e.g. Finally enter the LiveCD OS and then follow the prompts at the end of this article.įormat your USB drive in FAT32 type by system command or third-part tools.įor USB drive with large capacity, maybe there is no FAT32 option when you format it in Windows. Restart your computer (better to cold restart), and boot the USB device. ![]() 4.3 Reboot your computer, and select USB boot option.Just select the right device and ISO file and keep other options unchanged. ![]() Write the ISO file to the USB stick with rufus. 4.2 Write VentoyLiveCD ISO to the USB stick.Rufus is an open source tool with only 1.1MB size. Be careful not to select the wrong disk, so as not to format the system disk. If you don't have a normal Ventoy USB drive or it's your first time to install Ventoy, please refer any of the methods bellow.Īfter entering the Ventoy LiveCD OS, just follow the prompts at the end of this article to select the disk and install or update Ventoy. Put the LiveCD iso to the Ventoy USB drive and boot it as a normal ISO image by Ventoy. If you already have an USB drive with Ventoy in it and you just want to update it or you want to install Ventoy to another USB drive, you just need to Ventoy LiveCD is Tin圜ore Linux + Ventoy Linux install package. Directly use the LiveCD ISO and install Ventoy to the disk inside the VM. If you don't want to use USB drive, you can also test Ventoy with Virtual Machine. Linux users can directly use linux version of Ventoy, and no need to use this LiveCD.ģ. Ventoy LiveCD is only for Windows users, and only needed when Ventoy2Disk.exe always fail.Ģ. ![]() ![]() That is to say, Ventoy LiveCD is not the ISO version of Ventoy, it is just used to install Ventoy.ġ. Relatively speaking, the installation program of the Linux system directly uses the dd command provided by the system to write data, and there is almost no failure.īut users who use Windows systems generally do not have a Linux environment, so I provide a Ventoy LiveCD as plan B for Windows users. Of course, Ventoy2Disk.exe has been optimized and improved, but there are still more special cases. Therefore, the installation program of the Windows version often fails to install and upgrade in some systems. In Windows, there are many restrictions for these very low-level operations and this process is easily affected by other programs, such as anti-virus software, active system protection, etc. Ventoy will write data to the USB drive during installation and upgrade, it directly write to the physical sector, and also modifies the MBR and partition table. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |